Filters
Sort By
Price Range
Subcategories
Brands
EZ Finish Pro Applicator System
Shop EZ Finish Pro gym floor finish applicators for recoating and refinishing hardwood gym floors and basketball courts. These gravity-fed systems allow one operator to apply water-based or oil-based floor finishes directly from a tank, eliminating the need to pour finish onto the floor by hand.
The EZ Finish Pro EZ-450 is a complete applicator system and a modern alternative to the discontinued E-Z Way K-450. For contractors building custom applicators, the EZ-500 Dual Valve Tank Assembly provides the tank and valve components without the handle, applicator head, or pad. Shop our floor coater refills for replacement applicator pads.
Sort By
Price Range
Brands
Subcategories
Showing all 2 results
EZ-500 Dual Valve Floor Finish Tank Assembly For DIY Systems
SKU: EZ-500
$403.65
Off-the-shelf applicator systems do not always fit every custom workflow or specialized T-bar setup. The EZ-500 Dual Valve Tank Assembly provides the high-performance core of our professional system for those who prefer to build their own custom applicator. Featuring 100% 304 stainless steel components and an external control design, this assembly eliminates the mechanical failures common in modified poly-tanks. It allows you to integrate a professional-grade, gravity-fed delivery system into your existing equipment, ensuring a controlled, contamination-free finish application every time.
EZ Finish Pro EZ-450 Gym Floor Finish Applicator
SKU: EZ-450
$594.99
The EZ Finish Pro EZ-450 gym floor finish applicator gives contractors a gravity-fed alternative to the discontinued E-Z Way K-450. One operator applies finish to hardwood sports floors through 304 stainless steel valves.
Use the included 24-inch lambswool pad for oil-based finish OR the 24″ synthetic lambswool pad for water-based finishes.
How to Apply Gym Floor Finish with the EZ Finish Pro EZ-450
The EZ Finish Pro EZ-450 uses a gravity-fed, dual-valve system to deliver gym floor finish directly to the floor ahead of the applicator pad. Proper pad preparation, flow control, and application technique help achieve a smooth, consistent finish across large hardwood athletic floors.
- Prepare the Gym Floor: Screen or abrade the existing finish as required by the coating manufacturer. Thoroughly clean the floor and remove dust, dirt, and contaminants before application. Confirm that temperature, humidity, ventilation, and floor conditions meet the finish manufacturer’s requirements.
- Prepare and Install the Applicator Pad: Select the appropriate 24-inch natural lambswool or synthetic lambswool pad for your finish. Shake out the pad and remove loose fibers before installation. Position it flat against the applicator head, secure it with the clamps, attach the handle, and fasten the bungee cords.
- Fill the Applicator Tank: Fill the EZ-450’s 2.5-gallon translucent tank with a compatible gym floor finish. Follow the coating manufacturer’s instructions for product preparation, coverage, and handling. The translucent tank allows you to monitor the finish level throughout the application.
- Charge the Pad and Adjust the Valves: Open both flow-control valves to allow finish to reach and saturate the applicator pad before starting. Adjust the valves independently to distribute finish evenly across the full width of the applicator head. Set the flow rate based on the finish, room conditions, and your walking speed.
- Apply Finish in Long, Steady Passes: Begin in a corner, preferably farthest from your exit, and make a straight pass down the length of the gym. Maintain a slow, consistent walking speed and a wet edge. Overlap each full-length pass by approximately 4 to 6 inches. Keep a controlled puddle of finish approximately 1 to 1-1/2 inches ahead of the applicator pad, with the head held at a slight angle toward the unfinished floor. At the end of each pass, turn carefully and use a short pass along the end wall before beginning the next full-length pass. Adjust the valves as needed to prevent excess finish from accumulating near walls and corners.
- Monitor the Finish Level and Refill: As the tank empties, gravity-fed flow decreases. Monitor the finish level through the tank and refill before it drops below half full. Move the applicator onto an unfinished section of floor before refilling to prevent drips from landing on freshly coated areas. Maintain consistent flow, walking speed, and film thickness throughout the application.
- Clean the Applicator Immediately After Use: Drain remaining finish and handle or store it according to the coating manufacturer’s instructions. Remove the applicator pad and flush the tank, both valves, and associated fittings with the cleaning solution specified for the finish used. Flush both valves thoroughly until the cleaner runs clear. Wipe down the applicator and store it dry with the valves open. Never leave finish inside the applicator overnight.
Always follow the coating manufacturer’s drying, recoating, and curing instructions before allowing traffic or applying additional coats.
EZ Finish Pro Applicator System - Frequently Asked Questions
For schools and flooring contractors recoating full-size gymnasiums, the EZ-450 allows one operator to apply finish directly from a 2.5-gallon tank using independently adjustable valves. Based on customer feedback, experienced operators have coated 7,000 to 10,000 square feet in approximately one hour. Actual application times vary with floor size, finish type, and working conditions. For smaller areas, a T-bar applicator may be sufficient.
The EZ Finish Pro EZ-450 is a complete gravity-fed floor finish applicator system with a 2.5-gallon HDPE tank, dual stainless steel valves, 63-inch handle, and 24-inch applicator pad. Customers can order the EZ-450 with either a natural lambswool or synthetic lambswool pad, depending on their finish application. The EZ-500 uses the same HDPE tank and dual-valve assembly but is sold without the handle, applicator head, or pad for contractors building custom applicators.
Yes. The EZ-500 Dual Valve Tank Assembly is designed to mount to standard 1″ (15/16″) diameter mop handles and includes three stainless steel mounting bolts. Contractors can use it to build a custom gravity-fed floor finish applicator, including compatible T-bar configurations. The EZ-500 supplies finish directly to the floor through its dual valves, eliminating the need to repeatedly pour finish ahead of the applicator. Confirm the mounting arrangement and compatibility of your handle and applicator head before installation.
Clean the applicator immediately after each job to prevent finish from drying inside the valves and passages. Drain the remaining finish, then thoroughly flush the tank and both stainless steel valves using the cleaner recommended by the finish manufacturer. Continue flushing until the cleaner runs clear. Avoid soaking the valves in cleaning chemicals, and never leave finish in the applicator overnight. Proper cleaning and maintenance help keep the valves operating smoothly.
Get 10% off Your Next Order!
Sign up for exclusive updates, product announcements, and special offers delivered straight to your inbox. Plus, enjoy 10% off your next order (up to $50 of savings) as a thank you for joining! Good for new customers AND existing customers!












